u7cc彩票

冷再生施工和机械租赁业务
筑路架桥,奉献社会;以人为本,不断创新

服务热线

18264104888

u7cc彩票

首页>>u7cc彩票冷再生机时打滑的原因及方法

冷再生机时打滑的原因及方法

来源:http://gongyeliusuan.com/ 日期:2023-07-10 发布人:
客户在求租冷再生机使用过程中,不可避免地会出现消耗和磨损,其中,冷再生机输送带特别容易出现问题,运行时间长,可能出现打滑现象,影响工作效率。下面冷再生机出租厂家来分析下打滑的原因和解决办法。
Customers inevitably experience consumption and wear during the use of a cold recycling machine, among which the conveyor belt of the cold recycling machine is particularly prone to problems, long operation time, and may slip, affecting work efficiency. Let's analyze the reasons and solutions for the slipping of the cold regeneration machine rental manufacturer below.
1、初始张力太小。
1. The initial tension is too low.
输送带离开滚筒的张力不够,会引起皮带打滑。一般来说,这种情况是在启动时发生的。如果你想解决它,你必须调整张力装置和增加初始张力。
Insufficient tension of the conveyor belt leaving the drum can cause the belt to slip. Generally speaking, this situation occurs during startup. If you want to solve it, you must adjust the tension device and increase the initial tension.
2、摩擦力是不够的。
2. Friction is not enough.
传动滚筒与输送带之间的摩擦力不足以引起滑动。造成这种现象的主要原因是输送带上的水或环境潮湿。解决方法:在气缸中加入一些松香末。注意不要用手而应用鼓风设备吹入,以免发生事故。
The friction between the transmission drum and the conveyor belt is not sufficient to cause sliding. The main reason for this phenomenon is the water on the conveyor belt or the humid environment. Solution: Add some rosin powder to the cylinder. Be careful not to use your hands and blow in with an air blowing device to avoid accidents.
3、轴承损坏
3. Bearing damage
尾部滚子轴承损坏或不旋转。造成损坏的原因是机器尾部太浮、太沉,不能及时修理和更换损坏的或不灵活的部件,这导致由打滑引起的阻力增加。
The tail roller bearing is damaged or does not rotate. The reason for the damage is that the tail of the machine is too floating and heavy, and damaged or inflexible components cannot be repaired and replaced in a timely manner, resulting in increased resistance caused by slipping.
冷再生机出租
4、起步太快。
4. Starting too fast.
起动速度太快,不能打滑。这个时候可慢速启动。如果使用鼠笼电机,则可以移动两次,然后被激活,还可以有效地克服打滑现象。
The starting speed is too fast to slip. At this time, it can be started slowly. If a squirrel cage motor is used, it can be moved twice and then activated, effectively overcoming slipping.
5、输送带负荷过大。
5. The conveyor belt is overloaded.
输送带的负荷过大,超过电机能力也会打滑。打滑的优点是保护电机。否则,电动机将长期燃烧。但对于运行来说则是打滑事故。
The load of the conveyor belt is too large, and exceeding the motor capacity can also cause slipping. The advantage of slipping is to protect the motor. Otherwise, the motor will burn for a long time. But for operation, it is a slip accident.
以上是冷再生机时打滑的原因及方法相关信息的所有内容了,想要了解更多关于求租冷再生机相关内容,请继续关注浏览我们网站http://gongyeliusuan.com
The above is all the information about the reasons and methods of slipping during the cold recycling machine. If you want to learn more about renting a cold recycling machine, please continue to follow and browse our website http://gongyeliusuan.com .

推荐阅读/ Recommended reading

u7cc彩票一般来说,长期经受重型交通的路面会出现路基损坏的情况。为了消除这种损坏,需要对整个路面进行结构性维修。路面冷再生机将铣刨料全部进行重新利用,加之其经济的处理方式,使得采用泡沫沥青...

冷再生机租赁:冷再生机辅助液压系统介绍 2024-01-13
路面冷再生机的组成及原理介绍 2024-01-11
路面冷再生机设备的工作原理 2024-01-08
冷再生机是解决道路全深度翻新的平台 2024-01-05

推荐产品/ Recommended products